Chandrayaan-3 finds 3 distinct layers in Moon’s soil
ChaSTE observations from Chandrayaan-3’s Vikram lander revealed three distinct layers in the Moon’s shallow soil at Shiv Shakti Point. The result matters because it shows that even the upper 10 cm is not a uniform blanket: its physical and heat-transfer properties change with depth. The top layer extends to about 3 cm and is highly porous. From 3 to 6 cm is a middle layer with higher thermal conductivity. The bottom layer, from 6 to 10 cm, is denser and has intermediate thermal conductivity. The researchers reported that these fine-scale differences had not been observed or expected earlier. The profile came from ChaSTE measurements at Vikram’s original, pre-hop location. Earlier analysis of measurements after the lander’s hop found two layers, where engine firing had disturbed the uppermost 2–3 cm. The new profile adds the porous surface layer and offers a reference for comparing other landing sites and improving models of the Moon’s shallow subsurface.
What three layers did Chandrayaan-3 detect beneath the Moon’s surface at Shiv Shakti Point?
ChaSTE observations from Chandrayaan-3’s Vikram lander revealed three distinct layers in the Moon’s shallow soil at Shiv Shakti Point. The result matters because it shows that even the upper 10 cm is not a uniform blanket: its physical and heat-transfer properties change with depth.
The top layer extends to about 3 cm and is highly porous. From 3 to 6 cm is a middle layer with higher thermal conductivity. The bottom layer, from 6 to 10 cm, is denser and has intermediate thermal conductivity. The researchers reported that these fine-scale differences had not been observed or expected earlier.
The profile came from ChaSTE measurements at Vikram’s original, pre-hop location. Earlier analysis of measurements after the lander’s hop found two layers, where engine firing had disturbed the uppermost 2–3 cm. The new profile adds the porous surface layer and offers a reference for comparing other landing sites and improving models of the Moon’s shallow subsurface.
How deep is the measured soil profile, and how do the layers’ thicknesses and densities vary?
ChaSTE revealed a soil profile extending through the top 10 cm at Shiv Shakti Point. It is divided into three layers, and their boundaries do not make three equal-thickness sections. This short depth matters because the study found marked changes in the soil’s physical and thermal properties within it.
The upper layer runs from the surface to about 3 cm, so it is about 3 cm thick. The middle layer spans 3–6 cm, also about 3 cm. The bottom layer extends from 6–10 cm, making it about 4 cm thick. The article reports an estimated bulk density of about 600 kg per cubic metre for the uppermost soil, rising to about 1,500 kg per cubic metre at 10 cm.
It does not give a separate density value for each layer. Instead, it describes the middle as more thermally conductive than the other layers and the bottom as denser, with intermediate thermal conductivity. Soil cohesion also rises with depth, reaching about 1,350 pascals at 10 cm.
What is lunar regolith, and what does it consist of?
Lunar regolith is the loose layer of material covering the Moon’s surface. The article describes the surface as a blanket of dust and broken rock. In the standard scientific use of the term, regolith includes loose dust, soil-sized grains, and rock fragments; that fuller definition is general scientific context beyond the article’s wording.
The key point in this study is that regolith is not necessarily alike throughout its shallow depth. ChaSTE measurements at Shiv Shakti Point identified a highly porous upper layer to about 3 cm, a more thermally conductive middle layer from 3 to 6 cm, and a denser bottom layer from 6 to 10 cm. Their differing properties show why the word “soil” can hide important variation.
The finding provides a direct profile of the Moon’s southern high-latitude region. It can help scientists test models of the shallow subsurface and compare other landing sites with measured lunar conditions. It also matters for questions about how heat moves through the ground and whether migrating water could remain underground or be lost through sublimation.
How did ChaSTE measure the soil’s temperature and thermal properties?
ChaSTE, the Chandra’s Surface Thermophysical Experiment aboard Vikram, collected observations of the soil at Shiv Shakti Point. Those observations revealed how temperature and thermal properties vary with depth. The article reports a temperature gradient of about 73 kelvin across the top 10 cm at local noon, with each layer responding differently to solar heating.
The article does not explain the instrument’s operating steps. As general instrument context, a thermophysical probe can measure temperature at different depths using sensors, and estimate thermal conductivity by observing how the soil responds to heating. That describes the general method, not a procedure specified in this article.
The reported profile separates a porous upper layer, a more conductive middle layer, and a denser bottom layer. These measurements provide the first direct thermophysical profiling of the Moon’s southern high-latitude region. They also give scientists ground-truth data to compare with other landing sites and to improve models of the shallow lunar subsurface, where knowledge has depended largely on laboratory studies and theoretical estimates.
How might material thrown out by nearby crater impacts have formed the different layers?
Researchers propose that successive impacts from nearby craters may help explain the soil layers at Shiv Shakti Point. The idea matters because the measured differences in porosity, density, and thermal conductivity may reflect material deposited at different times, rather than one uniform soil layer.
The craters named in the study are Schomberger A, C2, and C1. Material thrown out by impacts could have landed around Shiv Shakti Point in separate deposits, each with different properties. Over time, those deposits may have formed the fine-scale layering measured by ChaSTE. This is an interpretation based on modelling and analysis of the surrounding terrain, not a directly observed sequence of events.
The measurements themselves show three layers within 10 cm: a highly porous surface, a more thermally conductive middle, and a denser bottom. The crater explanation is one proposed way to account for that profile. The results provide a ground-truth reference for future landing sites and constraints for models of the Moon’s shallow subsurface, but the article does not report a definitive cause for each layer.
How could the soil’s layers affect whether water is retained underground and where equipment or habitats could be placed?
The layers matter for two practical questions: whether water moving into shallow lunar soil might remain there, and where future equipment or habitats could be placed. The researchers say that porosity and thermal conductivity can influence whether water is retained or lost through sublimation. The article does not say that one particular layer guarantees retention.
At Shiv Shakti Point, the top 10 cm had a temperature gradient of about 73 kelvin at local noon, and the three layers responded differently to solar heating. The upper layer is highly porous, the middle layer has higher thermal conductivity, and the bottom layer is denser. A few centimetres below the surface, temperatures can vary markedly from those at the top.
Those temperature profiles could help engineers identify suitable depths for future habitats and equipment. The article notes that choosing a depth with different temperature variations could potentially reduce the need for active thermal management. The findings also offer a ground-truth reference for other landing sites, while helping scientists model how the shallow subsurface affects water and heat.
How do porosity and thermal conductivity determine how heat and water move through soil?
Porosity is the share of a soil’s volume made up of spaces between its particles. Thermal conductivity describes how readily heat moves through a material. These properties matter because the study found that they vary across the top 10 cm at Shiv Shakti Point, rather than staying uniform with depth.
The uppermost soil has an estimated porosity of about 80%, while the middle layer has higher thermal conductivity than the other layers. In general, the amount and arrangement of pore space can affect how water moves or remains in soil, while thermal conductivity affects how quickly heat spreads through it. The article does not say that higher porosity or conductivity alone always increases water retention.
The researchers say shallow porosity and thermal conductivity may influence whether migrating water is retained or lost through sublimation. The measured temperature gradient—about 73 kelvin across 10 cm at local noon—also shows why heat transfer matters. These findings can inform models of the shallow Moon and help engineers assess depths for future habitats and equipment.
This brief was written by AI from the original reporting and checked by other models. Names, figures and quotes come from the source; read it for full context.
Read more in the JupiteX app
Pulse is free. New stories every 4 hours, each one broken into the questions that explain it.
Or read more news on the web